1.4435 Stainless Steels to DIN 17440 (1996)
1.4435 - Specification & Application
- DIN 17440 (1996) - Stainless steels - Technical delivery conditions for drawn wire
- DIN 17441 (1997) - Stainless steels - Technical delivery conditions for cold rolled strips and slit coils strip and sheets cut from such strips for pressure purposes
- DIN 17455 (1985) - Welded circular tubes of stainless steels for general requirements; technical delivery conditions
- DIN 17456 (1985) - Seamless circular tubes of stainless steels for general requirements; technical delivery conditions
- DIN 17457 (1985) - Welded circular tubes of austenitic stainless steels for special requirements; technical delivery conditions
- DIN 17458 (1985) - Seamless circular tubes of austenitic stainless steels for special requirements; technical delivery conditions
- DIN EN 10028-7 - Flat products made of steels for pressure purposes - Part 7: Stainless steels
- DIN EN 10088-1 - Stainless steels - Part 1: List of stainless steels
- DIN EN 10088-2 - Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes
- DIN EN 10088-3 - Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
- DIN EN 10088-4 - Stainless steels - Part 4: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for construction purposes
- DIN EN 10088-5 - Stainless steels - Part 5: Technical delivery conditions for bars, rods, wire, sections and bright products of corrosion resisting steels for construction purposes
- DIN EN 10216-5 (2004) - Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 5: Stainless steel tubes
- DIN EN 10217-7 - Welded steel tubes for pressure purposes - Technical delivery conditions - Part 7: Stainless steel tubes
- DIN EN 10222-5 - Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels
- DIN EN 10250-4 - Open die steel forgings for general engineering purposes - Part 4: Stainless steels
- DIN EN 10253-3 - Butt-welding pipe fittings - Part 3: Wrought austenitic and austenitic-ferritic (duplex) stainless steels without specific inspection requirements
- DIN EN 10253-4 - Butt-welding pipe fittings - Part 4: Wrought austenitic and austenitic-ferritic (duplex) stainless steels with specific inspection requirements
- DIN EN 10272 - Stainless steel bars for pressure purposes
- DIN EN 10296-2 (2005) - Welded circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel
- DIN EN 10297-2 (2005) - Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel
Austenitic stainless steel. Grade 00Cr17Ni14Mo2 was replaced by new designation 022Cr17Ni12Mo2 according to GB/T 20878 (2007)
Chemical composition(wt.%) of 1.4435 grade: to DIN 17440 (1996)
| Elements |
Min.（≥） |
Max.（≤） |
Similar |
Remarks |
| C |
- |
0.030 |
|
|
| Si |
- |
1.00 |
|
|
| Mn |
- |
2.00 |
|
|
| P |
- |
0.035 |
|
|
| S |
- |
0.030 |
|
|
| Ni |
12.00 |
15.00 |
|
|
| Cr |
16.00 |
18.00 |
|
|
| Mo |
2.00 |
3.00 |
|
|
1.4435 - Detail
Stainless and heat resisting steels
Mechanical properties of grade 1.4435 DIN 17440 (1996)
Proof strength
Rp0.2 (MPa) |
Tensile strength
Rm (MPa) |
Impact energy
KV (J) |
Elongation at fracture
A (%) |
Reduction in cross section on fracture
Z (%) |
As-Heat-Treated Condition |
Brinell hardness (HBW) |
| 325 (≥) |
867 (≥) |
13 |
14 |
42 |
Solution and Aging, Annealing, Ausaging, Q+T,etc |
344 |
Physical properties of grade 1.4435 DIN 17440 (1996)
| Property |
Density
kg/dm3 |
Temperature T
°C/F |
Specific heat
J / kgK |
Thermal conductivity
W/mK |
Electric resistance
µΩ·cm |
Modulus of elasticity
kN/mm2 |
Expansion rate |
| 132 (≥) |
725 (≥) |
44 |
34 |
31 |
Solution and Aging, Annealing, Ausaging, Q+T,etc |
214 |
Temp.
°C/°F |
Creep strain limit
(10000h)
(Rp1,0) N/mm2 |
Creep rupture strength
(10000h)
(Rp1,0) N/mm2 |
|
|
|
|
|
| 466 |
486 |
662 |
|
|
|
|
Product shapes we supply: